ในการออกแบบทางอิเล็กทรอนิกส์ ความแม

In electronic design, the required precision resistance may need attention in creating the patience of resistor based on the specific usage of it. In addition, the value of temperature coefficient of resistance, yet there may be a concern in some applications that require precision. The resistance in practice, also indicated that the maximum power level, which must exceed the thermal distribution of the resistor that is expected to occur in a specific cycle. This is the main concern for use with power electronics. The resistance rate is higher than it would have a larger size and may require the use of heat sink in high-voltage circuits, sometimes they need to pay attention to the working pressure ratio maximum of resistor. If you do not observe the voltage to the minimum working for the resistance. The failure may cause burning of the resistance. When the current through itตัวต้านทานในทางปฏิบัติมีค่าการเหนี่ยวนำต่ออนุกรมและค่าการเก็บประจุขนาดเล็กขนานอยู่กับมัน ข้อกำหนดเหล่านี้จะมีความสำคัญในการใช้งานความถี่สูง ในตัวขยายสัญญาณเสียงรบกวนต่ำหรือพรีแอมป์ ลักษณะการรบกวนของตัวต้านทานอาจเป็นประเด็น การเหนี่ยวนำที่ไม่ต้องการ, เสียงรบกวนมากเกินไปและค่าสัมประสิทธิ์อุณหภูมิ เหล่านี้จะขึ้นอยู่กับเทคโนโลยีที่ใช้ ในการผลิตตัวต้านทาน ปกติพวกมันจะไม่ได้ถูกระบุไว้เป็นรายต้วของตัวต้านทานที่ถูกผลิตโดยใช้เทคโนโลยีอย่างใดอย่างหนึ่ง ตระกูลของ ตัวต้านทานเดี่ยวก็มีคุณลักษณะตาม form factor ของมัน นั่นคือ ขนาดของอุปกรณ์และตำแหน่งของขา (หรือขั้วไฟฟ้า) ซึ่งมีความเกี่ยวข้องในการผลิตจริงของวงจรที่นำมันไปใช้

In electronic design The precision required of resistance may have an interest in creating tolerance of the resistor according to the specific use of it. The temperature coefficient of resistance, it could be a concern in certain applications that require precision. Resistors in practice has been identified as having the highest energy levels, which must exceed the thermal dissipation of the resistor that is expected to occur in the circuit. This is a major concern in applications with power electronics. Resistance rates are higher than would be larger and may require a heat sink in high-voltage circuit. Sometimes you have to pay attention to the maximum operating voltage of the resistor. If not considering the voltage to work for minimum resistance. Failure may cause burning of the resistor. When the current through it
in practice resistor in series with the inductor and capacitors small, parallel to it. These requirements are particularly important in high frequency applications. In a low-noise amplifier or pre-amplifier. The noise of the resistor may be an issue. Induction unwanted, excessive noise and temperature coefficient. These are based on the technology used. In the production of antibodies Usually they will not be listed on a sample of antibodies that are produced using one single family of resistors is featured by its form factor is the size of the device and the position of the legs. (Or electrodes) which are involved in the actual production of the circuit used them.

In electronics design. The precision required of resistance may need attention in the construction of its specific ตามการใช้งาน resistor toleranceThe resistor in practice also were identified that the maximum energy levels, which must be more than กระจายความร้อน resistor is expected to occur in the circuit. This is a major concern for use with electronic power.Heat sink circuit high voltage. Sometimes you have to pay attention to the rate of the maximum working pressure of the resistance. If not considering the voltage in the work the minimum for the resistance.When a current flows through it!In practice, the induction on the series resistor and capacitor in parallel, small อยู่กับมัน collection value These requirements will be important in the use of high frequency. In low noise amplifier or preamp.Induction of that want,Too much noise coefficient and temperature. These will depend on the technology used in the production of resistors. Normally they are not listed as samples of the resistor is produced by technology, either.It features a single resistor according to its form factor, that is, the size of the equipment and the position of the leg (or pole). , which are relevant in the actual production of circuit that brought it
.