สภาพการสึกหรอและผลทดสอบการสึกหรอทั้

สภาพการสึกหรอและผลทดสอบการสึกหรอทั้งหมด พบว่าอยู่ในช่วงปกติ
ความหนืดที่เปลี่ยนแปลงอาจจะเกิดจากการปนเปื้อนของแก๊สในน้ำมันหล่อลื่น
พบปริมาณเล็กน้อยของน้ำ เจือปนในน้ำมัน
ผลการตรวจนับอนุภาคสิ่งสกปรกชี้ว่าระดับความสะอาดของน้ำมันใกล้จะยอมรับไม่ได้แล้ว
สังเกตค่าผลทดสอบบางอย่างเข้าใกล้ค่าเตือนภัยหรือสูงกว่าเล็กน้อย แต่อาจพิจารณาว่ายังไม่รุนแรงมากนักในขณะนี้
แนะนำว่าไม่จำเป็นต้องเปลี่ยนถ่ายน้ำมันในขณะนี้ น้ำมันยังมีสภาพเหมาะสมที่จะใช้งานต่อได้ ยังคงเก็บตัวอย่างอย่างต่อเนื่อง

ผลลัพธ์ (อังกฤษ) 1:

Conditions of wear and all wear test results. I found that in normal range
changed viscosity may be caused by contamination of lubricating oil in the gas, the quantity of water is found a little
. Adulterated oil in
Dirt particle counting results suggest that the level of cleanliness of the oil near the note has not been accepted, some test result value
close up or slightly higher than the alarm, but it may be considered a very mild now
.Suggests that there is no need to change the oil at this time. There is also oil suitable condition to be used. Keep samples continuously.

ผลลัพธ์ (อังกฤษ) 2:

Conditions, wear and wear all the test results. Found to be in the normal range
viscosity changes may be caused by contamination of the gas in the oil.
showed a small amount of water Oil additives i = 0> conditions, wear and wear all the test results. Found to be in the normal range viscosity changes may be caused by contamination of the gas in the oil. showed a small amount of water Oil additives i = 0> conditions, wear and wear all the test results. Found to be in the normal range viscosity changes may be caused by contamination of the gas in the oil. showed a small amount of water Oil additives Found to be in the normal range viscosity changes may be caused by contamination of the gas in the oil. showed a small amount of water Oil additives Found to be in the normal range viscosity changes may be caused by contamination of the gas in the oil. showed a small amount of water Oil additives i = 1> Viscosity changes may be caused by contamination of the gas in the oil. showed a small amount of water Oil additives i = 1> Viscosity changes may be caused by contamination of the gas in the oil. showed a small amount of water Oil additives
Result of the dirt particles indicated that the level of cleanliness of petrol to be unacceptable.
observe the results of some tests to get to the alarm or slightly higher. I may consider that it is not serious, now.
Suggest that there is no need to change the oil now. The oil also has a right to continue using it. Continued to collect samples continuously.

ผลลัพธ์ (อังกฤษ) 3:

The state of wear and wear test results Found in the normal range
viscosity changes may be caused by contamination of the gas in the oil in casting, found a small quantity of water.

. Additives in oilThe results indicate that the particle count dirt clean level of oil almost unacceptable
สังเกตค่า some test results closer to the warning or slightly higher But may consider that are not very serious now
Suggest to change the oil in the now The oil also conditions suitable to use on Still collected continuously