1. Please open the printer cover an

1. Please open the printer cover and when the carriage head moves to center pull out the power cord.
2. The Purge unit is on the right side. Use a flashlight and you will see two ink pads. This is where the print-head is PARKED and is the top of the Purge unit.
3. There you will find wiper blades that move from the rear to the front. They wipe the bottom of the print-head when it is parked.
(The ink pads actually drop down about 3/4" to allow the wiper blade to pass and then it is supposed to spring back to the rear. Also the ink suction for cleaning the print-head is done by the purge unit.)
4. Use some rubber gloves and a paper towel and see if you can press the ink pads down just a little bit - about 1/4". See if for some reason the wiper blade is stuck extended, if so see if you can get it unstuck. Please do this gently such that you don't break anything there.

This error indicates that the purge unit is not giving the correct timing signal as it rotates inside 360 degrees. Therefore, something is either broken or jammed inside. If you had a paper jam and tried to forcefully pull it out, you could have pulled the internal gears out of alignment.

So you will need to do some maneouvers to try to release the cartridge from its parking position. Again, don't try hard.

Now, if this does not work than it would be cheaper to buy a new printer rather than sending it to Canon for repair if its not in warranty.

ผลลัพธ์ (อังกฤษ) 1:

One. please open the printer cover and when the carriage head moves to center pull out the power cord.
2. the purge unit is on the right side. use a flashlight and you will see two ink pads. this is where the print-head is parked and is the top of the purge unit.
3. there you will find wiper blades that move from the rear to the front. they wipe the bottom of the print-head when it is parked.
(The ink pads actually drop down about 3/4 "to allow the wiper blade to pass and then it is supposed to spring back to the rear. Also the ink suction for cleaning the print-head is done by the purge unit.)
. 4. use some rubber gloves and a paper towel and see if you can press the ink pads down just a little bit - about 1/4 ". see if for some reason the wiper blade is stuck extended,.if so see if you can get it unstuck. please do this gently such that you don't break anything there.

This error indicates that the purge unit is not giving the correct timing signal as it rotates inside 360 ​​degrees. therefore, something is either broken or jammed inside. if you had a paper jam and tried to forcefully pull it out, you could have pulled the internal gears out of alignment.

.so you will need to do some maneouvers to try to release the cartridge from its parking position. again, don't try hard.

now, if this does not work than it would be cheaper to buy a new printer rather than sending it to canon for repair if its not in warranty.
.

ผลลัพธ์ (อังกฤษ) 3:

false(The ink pads actually drop down about 3/4, to allow the wiper blade to pass and then it is supposed to spring back to the rear. Also the ink suction for cleaning the print-head is done by the purge unit.)
4. Use some rubber gloves and a paper towel and see if you can press the ink pads down just a little bit - about 1/4." If for some reason the See wiper blade is stuck extended,If so see if you can get it unstuck.Please do this gently such that you don' T break anything there.

This purge error indicates that the unit is not giving the correct timing signal as it rotates 360 degrees inside. Therefore, something is either broken or jammed inside. If you had a paper jam and forcefully tried to pull it out, you could have pulled the internal gears out of alignment.

You will need to do some So maneouvers to try to release the cartridge from its parking position. Again, don' T try hard.

Now, if this does not work than it would be cheaper to buy a new printer rather than sending it to Canon for repair if not in its warranty.