TOA GLIPTON1. Identification of the

TOA GLIPTON
1. Identification of the substance/preparation and of the company/undertaking
Product name and/or code : TOA GLIPTON ENAMEL
Type of Product : Alkyd air dry paint
Supplier/Manufacturer : TOA PAINT (THAILAND) CO.,LTD
31/2 Moo 3 , Bangna-Trad Rd.,KM.23 Bangsaothong.
Amphur Bangsaothong , Samuthprakarn 10541, Thailand
Tel : [phone]
Fax : [phone]
Emergency telephone number : Factory Tel. [phone]
Product use : Alkyd enamel paint
2. Composition/information on ingredients
Chemical name CAS no. EC Number % Classification
Alkyd Long Oil Resin 68333-62-0 - 50 -
Titanium Dioxide 13463 - 67 - 7 - 25 -
white sperit 64742-82-1 - 21 -
2-Ethylhexanoic Acid 149-57-5 - 1 -
Zirconium 2-Ethyl Hexanoate 22464-99-9 - 2 -
Cobalt 2 -Ethyl Hexanoate 136-52-7 - 1 -
3. Hazards identification
Flammable.
Irritating to eyes and skin.
Repeated exposure may cause skin dryness or cracking.
Harmful by inhalation and in contact with skin.
4. First aid measures.
General : In all cases of doubt, or when symptoms persist, seek medical attention. Never give
anything by mouth to an unconscious person.
Inhalation : Remove to fresh air. Keep person warm and at rest. If not breathing, if breathing is
irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained
personnel. Give nothing by mouth. If unconscious place in recovery position and seek
medical advice.
Skin contact : Remove contaminated clothing and shoes. Wash skin thoroughly with soap and water or
use recognised skin cleanser. Do NOT use solvents or thinners.
Eye Contact : Check for and remove any contact lenses. Immediately flush eyes with running water for
at least 15 minutes, keeping eyelids open.
Ingestion : If swallowed, seek medical advice immediately and show the container or label. Keep
person warm and at rest. Do not induce vomiting.
5. Fire-fighting measures
Extinguishing Media : Recommended: alcohol resistant foam, CO2, powders, water spray.
Not to be used : waterjet.
Recommendations : Fire will produce dense black smoke. Exposure to decomposition products may cause
a health hazard. Appropriate breathing apparatus may be required. Cool closed containers
exposed to fire with water. Do not release runoff from fire to sewers or waterways.
6. Accidental release measures
Personal Precautions : Exclude sources of ignition and ventilate the area. Avoid breathing vapour or mist. Refer
to protective measures listed in sections 7 and 8.
Spill : Contain and collect spillage with non-combustible absorbent materials, e.g. sand, earth,
vermiculite, diatomaceous earth and place in container for disposal according to local
regulations (see section 13). Do not allow to enter drains or watercourses . Clean preferably
with a detergent; avoid use of solvents. If the product contaminates lakes, rivers or sewage,
MATERIAL SAFETY DATA SHEET
Page 1 of 4
TOA GLIPTON
inform appropriate authorities in accordance with local regulations.
7. Handling and storage
Handling : Vapours are heavier than air and may spread along floors. Vapours may form explosive
mixtures with air. Prevent the creation of flammable or explosive concentrations of vapour in
air and avoid vapour concentration higher than the occupational exposure limits.
In addition, the product should only be used in areas from which all naked lights and other
sources of gnition have been excluded. Electrical equipment should be protected to the
appropriate standard.
To dissipate static electricity during transfer, earth drum and connect to receiving container
with bonding strap. Operators should wear anti-static footwear and clothing and floors
should be of the conducting type.
Keep container tightly closed. Keep away from heat, sparks and flame. No sparking tools
should be used.
Avoid contact with skin and eyes. Avoid the inhalation of dust, particulates and spray mist
arising from the application of this preparation. Avoid inhalation of dust from sanding.
Eating, drinking and smoking should be prohibited in area where this material is handled,
stored and processed. Workers should wash hands and face before eating, drinking and
smoking.
Put on appropriate personal protective equipment (see Section 8).
Never use pressure to empty : container is not a pressure vessel. Always keep in containers
of same material as the original one.
Comply with the health and safety at work laws.
When operators, whether spraying or not, have to work inside the spray booth, ventilation is
unlikely to be sufficient to control particulates and solvent vapour in all cases. In such
circumstances they should wear a compressed air-fed respirator during the spraying
process and until such time as the particulates and solvent vapour concentration has fallen
below the exposure limits.
Storage : Store in accordance with local regulations. Observe label precautions. Store in a cool,
well-ventilated area away from incompatible materials and ignition sources.
Keep away from: oxidising agents, strong alkalis, strong acids.
No smoking. Prevent unauthorised access. Containers which are opened must be carefully
resealed and kept upright to prevent leakage.
Do not empty into drains..
8. Exposure controls/personal protection
Engineering measures : Provide adequate ventilation. Where reasonably practicable this should be achieved by the
use of local exhaust ventilation and good general extraction. If these are not sufficient to
maintain concentrations of particulates and solvent vapour below the OEL, suitable respiratory
protection must be worn.
Ingredient name
Reaction product
Personal protective equipment
Respiratory system : If workers are exposed to concentrations above the exposure limit they must use appropriate,
certified respirators. Use respiratory mask with charcoal and dust filter when spraying this
product(as filter combination A2-P2).In confined spaces use compressed air or fresh air
respiratory equipment.When use of roller or brush, consider use of charcoalfilter (A2).
Skin and body : Personnel should wear anti-static clothing made of natural fibre or of high temperature
resistant synthetic fibre.
Hands : For prolonged or repeated handling, use gloves: polyvinyl alcohol or nitrile.
: Barrier creams may help to protect the exposed areas of the skin, they should however not
be applied once exposure has occurred.
For right choice of glove materials, with focus on chemical resistance and time of penetration,
seek advice by the supplier of chemical resistant gloves.
Eyes : Use safety eyewear designed to protect against splash of liquids.
Page 2 of 4
TOA GLIPTON
9. Physical and chemical properties
Physical state : Liquid.
Odour : Solvent smell
Colour : follow Catalog
Flash point : Closed cup: 5°C
Density : 1.00 - 1.10 g/cm3
Solubility in water : Insoluble
10. Stability and reactivity
Stability : Stable under recommended storage and handling conditions (see section 7).
Hazardous Decomposition Products : carbon monoxide, carbon dioxide, smoke, oxides of nitrogen.
strong exothermic reactions : oxidising agents, strong alkalis, strong acids.
11. Toxicological information
General : There are no data available on the preparation itself. The preparation has been assessed
following the conventional method of the Dangerous Preparations Directive 1999/45/EC and
classified for toxicological hazards accordingly . See Chapters 2 and 15 for details.
Skin Contact : Repeated or prolonged contact with the preparation may cause removal of natural
fat from the skin resulting in non-allergic contact dermatitis and absorption through the skin.
Eye Contact : The liquid splashed in the eyes may cause irritation and reversible damage.
Ingestion : Symptoms and signs include headache, dizziness, fatigue, muscular weakness,
drowsiness and in extreme cases, loss of consciousness.
12. Ecological information
Ecotoxicity data
Ingredient name Species Period Result
13. Disposal considerations
Do not allow to enter drains or watercourses. Material and/or container must be disposed of as hazardous waste.
European waste catalogue : 08 01 11 waste paint and varnish containing organic solvents or other dangerous
(EWC) substances
14. Transport information
Proper shipping name Paint Packing group 3 Label
UN. Number 1263 Class 3
Transport in accordance with ADR/RID, IMDG/IMO and ICAO/IATA and national regulation.
ADR/RID: Viscous substance. Not restricted, ref. chapter 2.2.3.1.5 (applicable to receptacles < 450 litre capacity)
IMDG: Viscous substance. Transport in accordance with paragraph 2.3.2.5 (applicable to receptacles

ผลลัพธ์ (อังกฤษ) 2:

TOA GLIPTON
1. Identification of the Substance / Preparation and of the Company / undertaking
Product name and / or code: TOA GLIPTON ENAMEL
Type of Product: Air Dry Alkyd Paint
Supplier / Manufacturer: TOA PAINT (THAILAND) CO., LTD
31/2 Moo 3, Bangna. -Trad Rd., KM.23 Bangsaothong.
Amphur Bangsaothong, Samuthprakarn 10541, Thailand
Tel: [phone]
Fax: [phone]
telephone Emergency Number: Factory Tel. [phone]
Product use: Alkyd enamel Paint
2. Composition / information on ingredients
Chemical name CAS no. EC Classification Number%
Alkyd Resin Long Oil 68333-62-0 - 50 -
Titanium Dioxide 13463 - 67 - 7 - 25 -
White Sperit 64742-82-1 - 21 -
149-57-5 2-Ethylhexanoic Acid - 1 -
2 Zirconium. -Ethyl hexanoate 22464-99-9 - 2 -
-Ethyl hexanoate 136-52-7 Cobalt 2 - 1 -
3. Hazards identification
Flammable.
Irritating to eyes and Skin.
Repeated exposure May Cause Skin dryness or cracking.
Harmful by inhalation and in Contact with Skin.
4. First Aid measures.
General: In all Cases of doubt, or when symptoms PERSIST, Seek Medical Attention. Never give
anything by Mouth to an Unconscious person.
Inhalation: Remove to Fresh Air. Keep person warm and at rest. If not breathing, if breathing is
irregular or if respiratory arrest occurs, provide artificial respiration or Oxygen by trained
Personnel. Give nothing by mouth. If Unconscious Place in Recovery position and Seek
Medical Advice.
Skin Contact: Remove contaminated Clothing and shoes. Skin Wash thoroughly with soap and Water or
use recognized Skin cleanser. Do NOT use solvents or thinners.
Eye Contact: Check for and Remove Contact Lenses any. Water immediately flush eyes with running for
at least 15 minutes, keeping eyelids open.
Ingestion: If swallowed, Seek Medical Advice immediately and the Container or Label Show. Keep
Warm and at Rest person. Do not induce vomiting.
5. Fire-Fighting measures
Extinguishing Media: Recommended: alcohol resistant foam, CO2, powders, Water Spray.
Not to be used: waterjet.
Recommendations: Fire Will Produce dense Black Smoke. Exposure to decomposition products May Cause
a Health Hazard. Appropriate breathing apparatus may be required. Closed Containers cool
exposed to Fire with Water. Do not release runoff to sewers or waterways from Fire.
6. Accidental release measures
Personal Precautions: Exclude Sources of ignition and ventilate the Area. Avoid breathing vapour or mist. Refer
to Protective measures listed in Sections 7 and 8.
Spill: Contain and collect with non-combustible absorbent Spillage Materials, eg Sand, Earth,
vermiculite, Diatomaceous Earth and Place in Container for Disposal according to local
regulations (See section 13). Do not allow to enter drains or watercourses. Clean preferably
with a Detergent; avoid use of solvents. If the product contaminates Lakes, Rivers or Sewage,
MATERIAL SAFETY DATA SHEET
Page 1 of 4
TOA GLIPTON
inform appropriate in accordance with local regulations Authorities.
7. Handling and Storage
Handling: vapors are heavier than Air and May spread Along Floors. Explosive vapors May form
mixtures with Air. Prevent the Creation of FLAMMABLE or Explosive vapor in concentrations of
Air and Avoid Higher than the vapor concentration Limits Occupational exposure.
In addition, the product should only be used in areas from which all Naked Lights and Other
Sources of Gnition have been excluded. Electrical Equipment should be Protected to the
appropriate standard.
To dissipate static during Electricity Transfer, Earth Connect to receiving Container drum and
bonding with Strap. Wear Anti-static operators should Footwear and Clothing and Floors
should be of the conducting Type.
Keep Container tightly Closed. Keep away from heat, sparks and flame. No sparking Tools
should be used.
Avoid Contact with Skin and eyes. Avoid the inhalation of dust, particulates and Spray Mist
Arising from the Application of this Preparation. Avoid inhalation of dust from Sanding.
Eating, drinking and smoking should be Prohibited Area in Material where this is handled,
stored and Processed. Workers should Hands and Face Wash before eating, drinking and
smoking.
Put on appropriate Personal Protective Equipment (See Section 8).
Never use pressure to Empty: Container is not a pressure Vessel. Always Keep in Containers
of Same Material As the Original one.
Comply with the Health and safety at Work Laws.
When operators, whether spraying or not, have to Work Inside the Spray Booth, Ventilation is
unlikely to be sufficient to Control particulates and Solvent vapor. in all cases. In such
circumstances they should Wear a Compressed Air Respirator-fed during the spraying
Process and until such time Solvent As the particulates and vapor concentration has fallen
Below Limits the exposure.
Storage: Store in accordance with local regulations. Observe label precautions. Store in a cool,
well-ventilated Area Away from incompatible Sources Materials and ignition.
Keep Away from: oxidising agents, strong alkalis, strong acids.
No smoking. Prevent unauthorised access. Containers which are opened must be carefully
resealed and kept Upright to Prevent leakage.
Do not Empty into drains ..
8. Exposure Controls / Personal Protection
Engineering measures: Provide adequate Ventilation. Where this should be achieved reasonably Practicable by the
use of local exhaust Ventilation and good general extraction. If these are not sufficient to
maintain concentrations of particulates and Solvent vapor Below the OEL, suitable respiratory
Protection must be worn.
Ingredient name
Reaction product
Personal Protective Equipment
Respiratory System: If Workers are exposed to concentrations above the exposure Limit they must use appropriate,
Certified. respirators. Use respiratory mask with charcoal and dust Filter when spraying this
product (combination A2-P2 As Filter) .in confined Spaces use Compressed Air or Fresh Air
respiratory Equipment.When use of Roller or brush, consider use of Charcoalfilter (A2).
Skin and. Body: Personnel should Wear Anti-static Clothing Made of Natural Fibre or of High Temperature
resistant synthetic Fibre.
Hands: For prolonged or repeated Handling, use gloves: polyvinyl alcohol or nitrile.
: Barrier creams May help to Protect the exposed areas of the Skin. , they should however not
be Applied once exposure has occurred.
For right Choice of glove Materials, with Focus on Chemical resistance and time of Penetration,
Seek Advice by the Supplier of Chemical resistant gloves.
Eyes: Use safety Eyewear designed to Protect against Splash of. liquids.
Page 2 of 4
TOA GLIPTON
9. Chemical and physical properties
Physical State: Liquid.
Odour: Solvent Smell
Colour: follow Catalog
Flash Point: Closed Cup: 5 ° C
Density: 1.00 - 1.10 G / cm3
Solubility in Water: Insoluble
10. Stability and reactivity
Stability: Stable under Recommended Storage and Handling conditions (See section 7).
Hazardous Decomposition Products: carbon monoxide, carbon dioxide, Smoke, oxides of nitrogen.
strong exothermic reactions: oxidising agents, strong alkalis, strong acids.
11. Toxicological information
General: There are no Data Available on the Preparation Itself. Preparation has been the Assessed
following the conventional method of the Dangerous Preparations Directive 1999/45 / EC and
classified for toxicological hazards accordingly. See Chapters 2 and 15 for details.
Skin Contact: Repeated or prolonged Contact with the Preparation May Cause Removal of Natural
FAT from the Skin resulting in non-allergic Contact dermatitis and absorption Through the Skin.
Eye Contact: The Liquid splashed in the eyes May. Cause irritation and reversible damage.
Ingestion: Symptoms and Signs include headache, dizziness, fatigue, muscular weakness,
drowsiness and in Extreme Cases, loss of consciousness.
12. Ecological information
Ecotoxicity Data
Ingredient name Species Period Result
13. Disposal Considerations
Do not Allow drains or watercourses to Enter. Material and / or Container must be disposed of hazardous waste As.
European waste Catalogue: 08 01 11 Paint and Varnish waste containing Organic solvents or Other Dangerous
(EWC) Substances
14. Transport information
Proper shipping name Paint Label 3 Packing Group
UN. Number 1263 Class 3
Transport in accordance with ADR / RID, IMDG / IMO and ICAO / IATA and National Regulation.
ADR / RID: Viscous Substance. Not restricted, ref. Chapter 2.2.3.1.5 (applicable to Receptacles <450 liter capacity)
IMDG: Viscous Substance. Transport in accordance with paragraph 2.3.2.5 (applicable to receptacles.

ผลลัพธ์ (อังกฤษ) 3:

ผสมกับอากาศ ป้องกันการไวไฟหรือระเบิดความเข้มข้นของไอน้ำในอากาศและหลีกเลี่ยง
ไอความเข้มข้นสูงกว่าขีดจำกัดการอาชีพ .
นอกจากนี้ ผลิตภัณฑ์ที่ควรใช้ในพื้นที่ที่มีไฟเปลือยกายทั้งหมดและแหล่งข้อมูลอื่น ๆของ gnition
ได้รับการยกเว้น อุปกรณ์ไฟฟ้าควรป้องกัน

มาตรฐานที่เหมาะสมTOA GLIPTON
1. Identification of the substance / preparation and of the company / undertaking
Product name and / or code: TOA. GLIPTON ENAMEL
Type of Product: Alkyd air dry paint
Supplier / Manufacturer: TOA PAINT (THAILAND) CO, LTD
31 / 2, Moo 3 Bangna-Trad. Rd, KM.23 Bangsaothong.
Amphur Bangsaothong, Samuthprakarn 10541, Thailand
Tel: [phone]
Fax: [phone]
Emergency. Telephone number:Factory Tel. [phone]
Product use: Alkyd enamel paint
2. Composition / information on ingredients
Chemical name CAS, no. EC Number% Classification
Alkyd Long Oil Resin 68333-62-0 - 50 -
Titanium Dioxide 13463 - 67 - 7 - 25 -
white sperit 64742-82-1 - 21 -
2-Ethylhexanoic. Acid 149-57-5 - 1 -
Zirconium 2-Ethyl Hexanoate 22464-99-9 - 2 -
Cobalt 2 - Ethyl Hexanoate 136-52-7 - 1 -
3.If not breathing if breathing, is
irregular or if respiratory arrest occurs provide artificial, respiration or oxygen by. Trained
personnel. Give nothing by mouth. If unconscious place in recovery position and seek
medical advice.
Skin contact. : Remove contaminated clothing and shoes. Wash skin thoroughly with soap and water or
use recognised skin cleanser. Do NOT. Use solvents or thinners.
.Hazards identification
.
Flammable Irritating to eyes and skin.
Repeated exposure may cause skin dryness or cracking.
Harmful. By inhalation and in contact with skin.
4. First aid measures.
General: In all cases of doubt or when symptoms persist,,, Seek medical attention. Never give
anything by mouth to an unconscious person.
Inhalation: Remove to fresh air. Keep person. Warm and at rest.Water spray.
Not to be used: waterjet.
Recommendations: Fire will produce dense black smoke. Exposure to decomposition. Products may cause
a health hazard. Appropriate breathing apparatus may be required. Cool closed containers
exposed to fire. With water. Do not release runoff from fire to sewers or waterways.
6. Accidental release measures
Personal Precautions:Eye Contact: Check for and remove any contact lenses. Immediately flush eyes with running water for
at least, 15 minutes. Keeping eyelids open.
Ingestion: If swallowed seek medical, advice immediately and show the container or label. Keep
person. Warm and at rest. Do not induce vomiting.
5. Fire-fighting measures
Extinguishing Media: Recommended: alcohol resistant. Foam CO2 powders,,,Exclude sources of ignition and ventilate the area. Avoid breathing vapour or mist. Refer
to protective measures listed. In sections 7 and 8.
Spill: Contain and collect spillage with non-combustible, absorbent materials e.g. Sand earth
vermiculite,,,, Diatomaceous earth and place in container for disposal according to local
regulations (see section 13).Do not allow to enter drains or watercourses. Clean preferably
with a detergent; avoid use of solvents. If the product. Contaminates lakes rivers sewage, or, MATERIAL SAFETY DATA SHEET

Page 1 of 4

TOA GLIPTON inform appropriate authorities. In accordance with local regulations.
7. Handling and storage
Handling: Vapours are heavier than air and may spread along. Floors. Vapours may form explosive
.To dissipate static electricity, during transfer earth drum and connect to receiving container
with bonding strap. Operators. Should wear anti-static footwear and clothing and floors
should be of the conducting type.
Keep container tightly, closed. Keep away, from heat sparks and flame. No sparking tools
should be used.
Avoid contact with skin and eyes. Avoid the inhalation. Of, dustMixtures with air. Prevent the creation of flammable or explosive concentrations of vapour in
air and avoid vapour concentration. Higher than the occupational exposure limits.
In addition the product, should only be used in areas from which all naked. Lights and other
sources of gnition have been excluded. Electrical equipment should be protected to the
appropriate standard.
.Container is not a pressure vessel. Always keep in containers
of same material as the original one.
Comply with the health. And safety at work laws.
When operators whether spraying, or not have to, work inside the, spray booth ventilation is
unlikely. To be sufficient to control particulates and solvent vapour in all cases. In such
.Particulates and spray mist
arising from the application of this preparation. Avoid inhalation of dust from sanding.
Eating,, Drinking and smoking should be prohibited in area where this material is handled
stored, and processed. Workers should wash. Hands and face, before eating drinking and
.
smoking Put on appropriate personal protective equipment (see Section 8).
Never. Use pressure to empty:Circumstances they should wear a compressed air - fed respirator during the spraying
process and until such time as the particulates. And solvent vapour concentration has fallen
below the exposure limits.
Storage: Store in accordance with local, regulations. Observe label precautions. Store in, a cool
well-ventilated area away from incompatible materials and ignition sources.
Keep. Away from:Oxidising, alkalis strong agents strong, acids.
No smoking. Prevent unauthorised access. Containers which are opened must. Be carefully
resealed and kept upright to prevent leakage.
Do not empty into drains...
8. Exposure controls / personal protection
Engineering. Measures: Provide adequate ventilation. Where reasonably practicable this should be achieved by the
.Use of local exhaust ventilation and good general extraction. If these are not sufficient to
maintain concentrations of. Particulates and solvent vapour below, the OEL suitable respiratory
protection must be worn.


Ingredient name Reaction product Personal. Protective equipment
Respiratory system: If workers are exposed to concentrations above the exposure limit they must use. , appropriate
.Certified respirators. Use respiratory mask with charcoal and dust filter when spraying this
product (as filter combination. A2-P2). In confined spaces use compressed air or fresh air
respiratory equipment.When use of roller or brush consider use,, Of charcoalfilter (A2).
Skin and body: Personnel should wear anti-static clothing made of natural fibre or of high temperature
resistant. Synthetic fibre.Use safety eyewear designed to protect against splash of liquids.
Page 2 of 4

TOA GLIPTON 9. Physical and chemical properties
Physical. State: Liquid.
Odour: Solvent smell
Colour: follow Catalog
Flash point: Closed Cup: 5 ° C
Density: 1.00 - 1.10 g / cm3
Solubility. In water: Insoluble
10. Stability and reactivity
Stability:
Hands: For prolonged or, repeated handling use gloves: polyvinyl alcohol or nitrile.
: Barrier creams may help to protect. The exposed areas of, the skin they should however not
be applied once exposure has occurred.
For right choice of glove. Materials with focus, on chemical resistance and time, of penetration
seek advice by the supplier of chemical resistant. Gloves.
Eyes:Stable under recommended storage and handling conditions (see Section 7).
Hazardous Decomposition Products: carbon, monoxide. Carbon dioxide smoke oxides,, of nitrogen.
strong exothermic reactions: oxidising, alkalis strong agents strong, acids.
11.? Toxicological information
General: There are no data available on the preparation itself. The preparation has been assessed
.Following the conventional method of the Dangerous Preparations Directive 1999 / 45 / EC and
classified for toxicological hazards. Accordingly. See Chapters 2 and 15 for details.
Skin Contact: Repeated or prolonged contact with the preparation may cause. Removal of natural
fat from the skin resulting in non-allergic contact dermatitis and absorption through the skin.
Eye Contact:Material and / or container must be disposed of as hazardous waste.
European waste Catalogue: 08 01 11 waste paint and varnish. Containing organic solvents or other dangerous
(EWC) substances
14. Transport information
Proper shipping name Paint Packing. Group 3 Label
UN. Number 1263 Class 3
Transport in accordance with ADR / RID IMDG / IMO, and ICAO / IATA and national regulation.
ADR / RID:The liquid splashed in the eyes may cause irritation and reversible damage.
Ingestion: Symptoms and signs, include headache. ,,, dizziness fatigue muscular weakness
drowsiness and in, extreme cases loss of consciousness.
12. Ecological information
Ecotoxicity. Data
Ingredient name Species Period Result
13. Disposal considerations
Do not allow to enter drains or watercourses.Viscous substance. Not, restricted ref. Chapter 2.2.3.1.5 (applicable to receptacles < 450 litre capacity)
IMDG: Viscous. Substance. Transport in accordance with paragraph 2.3.2.5 (applicable to receptacles.