Figure 4.1 shows a CROSS CUT test adhesion 4.2.3 tool for measuring and analyzing the results of the third test method for determining the durability against heat from smoking standard DIN 68861 Part 6 trial heat. As can be seen the test results, it is best to test the heat from cigarettes, lit a cigarette, because the heat from the fire. I can see the surface is burned as well. The research was conducted by a piece of wood and coated sheet 8 to test the durability to heat the cigarette is put to test the durability of the paint surface. The cigarette to burn a fire to pass through to 10 mm before laying down on the surface through a coated ago. Then wait for the Boxing cigarette burns to 40 mm, then take the cigarette out. When a surface is damaged and burned skin, clean thoroughly with water. Or abrasive cleaners Test on a surface coated with latex paint. And coated with lacquer and eight sheets were analyzed to determine differences in color are 2 kinds of measurements were divided into six levels: 6A = unchanged 6B = gloss changes visible difference to the naked eye 6C =. The exterior surface does not change color change color 6D = Burning wood does not burn the skin and damage 6E = 4.2 image shows Cigarette Testing Equipment Test and Measurement Tools 4.2.4 Analysis of the test method. The four kinds of wood materials. Problems with water If water is leaking through the coating to give moldings with bruising, edema, water and waste products, such as mold, decay, so the colors used should be water resistant as well. With standard DIN 68861-1 is an experiment that is resistant to chemicals and other chemicals are present, another 27 kinds of chemical experiment with some more experiments and analyzes are made by coating a sheet of wood, then either 8 sheets. The original test surface protection from various chemicals. According to the final testing stage. The amount of chemicals used 5 cc frozen on the surface coating on the specimen. Painted with lacquer typical 10th position on the workpiece 8 sheets painted tire tests at different times of 10 seconds, 2 minutes, 10 minutes, 60 minutes or 1 hour, 5 hours and 16 hours, according to the standards set out. then analyzes the differences of the three types of surface DIN sixty-eight thousand eight hundred and sixty-one Part 1 Para Rubber Lacquers Tested Articles 1 A 1 B Duration Duration Result Result Result Duration Acetic Acid 16 01. H 0 0 60 min 60 min 0 H 0 16 02. Acid Lemon. 60 min 60 min 0 0 0 03. Sodium Carbonate H 2 min 16 min 0 0 2 0 2 04. Ammonia Water H 16 min min 0 2 0 0 60 05. Ethyl-alcohol H 16 min 60 min 0 0 06. White,. Red Wine and Land H 16 H 0 5 0 5 0 H 0 H 5 H 07. Beer 16 0 5 0 H H 0 16 16 08. Cola Drinks H H 0 16 0 0 09. Instant Coffee 16 H 16 H 16 H 0. 0 10. Black Tee 0 16 16 H H H 0 16 0 0 16 11. Black Current juice 16 H H H 0 16 0 0 16 12. Canned Milk 16 H H H 0 16 0 16 0 H 0 H 13. Water 16. 16 H 0 H 0 2 14. Gasoline 16 min min 0 2 0 0 15. Acetone 16 H 10 s 10 s 3 0 0 16. Ethylene Butylacrylate 16 H 10 s 10 s 3 0 0 16 17. Butter 16 H 16 H 0. H 0 0 18. Olive Oil 16 16 H H H 0 0 16 16 19. Mustard H 0 H 5 H 0 5 0 0 5 20. Cooking Salt 16 H H H 0 0 5 0 5 H H 21. Onions 16 0 5. H 0 H 0 16 16 22. Lipstick H H 3 16 0 0 10 H 23. Disinfectant 16 min 10 min 0 0 24. Black Ink Pen 0 16 16 H H H 3 3 16 16 25. Ink H H 16 0 3 16. 3 H H 26. Cleaning products 16 0 60 min 60 min 0 0 0 27. Cleaning solvents H 16 min 60 min 0 60 0 Table 4.2 Chemicals Article for test Ref. DIN 68861-1 measure was divided into six levels. as follows: 0 = do not see the difference on the surface 1 = hard to see the differences on the surface of the reflection of the shadow 2 = visible differences, some of the sheen on the surface, but the surface is not. Damaged 3 = a difference of gloss and color of the skin. But the surface is not damaged, 4 = a difference of gloss and color of the skin. Surface damage and minor surface damage, clear 5 = 4.3. The analysis compared the differences between the two types of color in this section is a discussion or analysis of the differences between the two kinds of colors by the survey is divided into three parts: 4.3.1 Analysis of testing. Cross cut to 4.3 visual comparison image surface tested the Cross cut of 4.3 image shows the surface of the problem through testing the Cross cut and appeared to be. Surface testing With good adhesion results comparable with conventional lacquer 4.3.2. Analysis of experiments Cigarette test at 4.4 visual comparison of the surface tested the Cigarette test Figure 4.4 shows the appearance of skin problems work through a test of Cigarette test and appearances. that Surface testing The effect of burning the skin on par with conventional lacquer 4.3.3. Analysis of experiments Chemical Resistance Figure 4.5 shows a comparison surface tested the Chemical resistance test Figure 4.5 shows the characteristics of the surface through testing the Chemical resistance test and. it appears that Surface testing The results of the skin in general equivalent to lacquer work.
การแปล กรุณารอสักครู่..