เป็นเพราะว่า measuring station มียา

เป็นเพราะว่า measuring station มียางอยู่แล้ว แต่ entrance station ส่งยางมาเพิ่มอีก1 แล้วเริ่มขั้นตอนการวัด
ทำให้อัพริมดาวน์ลงมาถูกยาง
วันที่ 11 ลูกค้าต้องการให้เปลี่ยนแปลงโปรแกรม ระหว่างที่รอซับคอนแทคแก้ไขปัญหา เซ็นเตอร์ไลน์ แต่เกิดความผิดพลาดในการสื่อสาร
Centering close -> Lifter down -> Upper rim down -> lower chuck close -> upper chuck open -> inflate -> centering open

Now changed PLC program back to original condition because if inflate while centering arm close it will be effect to mechanical
Part of centering unit, may tire explosion, bead sit position not OK. The current sequence as below

Centering close -> Lifter down -> Upper rim down -> lower chuck close -> upper chuck open -> centering open -> inflate

ปัญหานี้เกิดเป็นครั้งที่สอง มันไม่ใช่ความผิดพลาดในการแก้สเตป พีแอลซี

after remove upper rim from lower spindle of 46C-0580 and check condition found it still available.
operation check by manual mode found can workable ไม่มีชิ้นส่วนใดเสียหาย สามารถรันการผลิตได้ตามปกติ

ผลลัพธ์ (อังกฤษ) 1:

It is because there are already tyres measuring station entrance station to send Yang came to 1, and then start the measuring procedure. Make up the rim down to be rubber.11. to change the program while waiting for the Centre to perform troubleshooting, contact SAP, but an error in the communication.Centering close -> Lifter down -> Upper rim down -> lower chuck close -> upper chuck open -> inflate -> centering openNow changed PLC program back to original condition because if inflate while centering arm close it will be effect to mechanical Part of centering unit, may tire explosion, bead sit position not OK. The current sequence as belowCentering close -> Lifter down -> Upper rim down -> lower chuck close -> upper chuck open -> centering open -> inflate This problem occurs a second time. It is not an error to solve the station box. PL cafter remove upper rim from lower spindle of 46C-0580 and check condition found it still available.Operation manual mode by check found no workable parts which can damage can run production.

ผลลัพธ์ (อังกฤษ) 2:

Because measuring station with rubber tires, but the entrance station sent me another one. Then start the measurements
made ​​by the ups downs down the tires
on 11 customer wants to change the program. While waiting to mop contactor solutions. Center Line However, an error in communication
Centering close -> Lifter down -> Upper RIM down -> Lower Chuck close -> Upper Chuck open -> inflate -> Centering open Now changed PLC Program Back to Original condition because if inflate while Centering ARM. close it Will be Effect to Mechanical Part of Centering UNIT, May Tire Explosion, Bead SIT position not OK. The current Sequence As Below Centering close -> Lifter down -> Upper RIM down -> Lower Chuck close -> Upper Chuck open ->. centering open -> inflate the problem a second time. It is not the fault of the State of the PLC after RIM Remove from Lower Upper spindle of 46C-0580 and it still Found Available Check condition. Operation Check by manual mode Found Can not workable any damaged parts. Production can run normally.

ผลลัพธ์ (อังกฤษ) 3:

Because measuring station there already, but entrance station send another 1 rubber and measurement procedure
do make prim down down rubber
.The 11 customers need to change the program. While Roz and contactor fix center line but crashes in communication
Centering close - > Lifter down - > Upper rim. Down - > lower chuck close - > upper chuck open - > inflate - > centering open

.Now changed PLC program back to original condition because if inflate while centering arm close it will be effect to mechanical.
Part of centering unit may tire, explosion bead sit, position not OK. The current sequence as below

Centering close - >. Lifter down - > Upper rim down - > lower chuck close - > upper chuck open - > centering open - > inflate

.This problem was born a second time. It's not a mistake in solving step PLC

after remove upper rim from lower spindle of 46C-0580 and check condition found. It still available.
operation check by manual mode found can workable without any parts damaged, can run the production normally
.