Trimming technique at mixer trimmin

Trimming technique at mixer trimming process
Mixer trimming method is used same technique with PBS trimming.
However, mixer trimming process uses low power because phase of each polarize at mixer has to change in same angle. So, if power supplies gives high power as PBS trimming, phase of each polarize will shift as PBS trimming result. This will effect to next process which is PBS trimming process.
The DC power supplies give power around 2.2-2.5W. Mixer trimming process uses equipments as shown in Figure 6 which composes with 4 DC power supplies, stage controller, TEC controller, optical switch, ASE light source and SWS measurement system. 2 DC power supplies are used for trimming upper mixer while other two are used for lower mixer. ASE light source is used to alignment while tunable with SWS detector module is used to measurement polarize dependence loss (PDL).
Thin film heater at mixer part is at Y-brunch of both signal and LO as shown in Figure 7. The thin film heater connects with three electrodes. Electrode1 and electrode2 are anode while electrode 3 is common cathode. From these electrodes, the trimming procedure will change refractive index (phase angle) in pair of Y-branch, i.e. upper side of LO with lower side of signal and lower side of LO with upper side of signal. So, trimming at mixer will have some phase angle error because of relation of LO and signal thin film heater. That means trimming at mixer cannot change only each branch of Y-branch.

ผลลัพธ์ (อังกฤษ) 2:

Trimming Trimming Process Technique at Mixer
Mixer method is used Trimming Trimming Same Technique with PBS.
However, uses low Power Mixer Trimming Process because each phase of Polarize at Mixer has to Change in Same Angle. So, if power supplies gives high power as PBS trimming, phase of each polarize will shift as PBS trimming result. Will this Effect Process which is next to PBS Trimming Process.
The DC Power Supplies Power Around 2.2-2.5W give. Mixer trimming process uses equipments as shown in Figure 6 which composes with 4 DC power supplies, stage controller, TEC controller, optical switch, ASE light source and SWS measurement system. 2 DC power supplies are used for trimming upper mixer while other two are used for lower mixer. ASE Light source is used to while tunable Alignment with SWS Detector Module is used to measurement Polarize dependence loss (PDL).
Thin Film Heater at Part Mixer is at brunch of both Y-LO as shown in Figure 7. Signal and The thin Film Heater. connects with three electrodes. Electrode1 and electrode2 are anode while electrode 3 is common cathode. From these electrodes, the trimming procedure will change refractive index (phase angle) in pair of Y-branch, ie upper side of LO with lower side of signal and lower side of LO with upper side of signal. So, trimming at mixer will have some phase angle error because of relation of LO and signal thin film heater. That means trimming at mixer can not change only each branch of Y-branch.

ผลลัพธ์ (อังกฤษ) 3:

Trimming technique at mixer trimming process.Mixer trimming method is used same technique with PBS trimming.However mixer trimming, process uses low power because phase of each polarize at mixer has to change in same angle, So,. If power supplies gives high power as PBS trimming phase of, each polarize will shift as PBS trimming result. This will. Effect to next process which is PBS trimming process.The DC power supplies give power around 2.2-2.5W. Mixer trimming process uses equipments as shown in Figure 6 which composes. With 4 DC power supplies stage, controller, controller TEC, switch optical, light ASE source and SWS measurement system. 2 DC. Power supplies are used for trimming upper mixer while other two are used for lower mixer. ASE light source is used to alignment. While tunable with SWS detector module is used to measurement polarize dependence loss (PDL).Thin film heater at mixer part is at Y-brunch of both signal and LO as shown in Figure 7. The thin film heater connects. With three electrodes. Electrode1 and electrode2 are anode while electrode 3 is common cathode. From, these electrodes the. Trimming procedure will change refractive index (phase angle) in pair, of Y-branch i.e. Upper side of LO with lower side. Of signal and lower side of LO with upper side of signal. So trimming at, mixer will have some phase angle error because. Of relation of LO and signal thin film heater. That means trimming at mixer cannot change only each branch of Y-branch.