1. When the technicians goes to the

1. When the technicians goes to the customer site the technician will inquire to the customer about the nature of the machine problem.
2. Then, print the event report and check all error before working.
3. Open all machine covers including DM1, DM2 to check the belts, mechanical components of the machine (test mode). Check if there are problems.
4. Turn off the machine, start cleaning the machine - should close Unit Sensor before using the blower. After finished cleaning take out the Sensor Unit for cleaning.
5. Check the position of Suction Band and Rocker Tray set if it is in correct position, check the thickness of suction band and properly adjust the locker tray.
6. Always check the Valve Rotor, when the technician goes to PM check the bearing inside if it is abnormal change or repair immediately.
7. Check Belt, O-ring, Toothed wheel include all bearings of the whole machine if damaged or if the bearing does not fit together the technician should change or repair immediately.
8. Check sensor unit, remove Roller (Part no.158853011) Brass bearing (Part no.201448000) for cleaning and check if it is turning smoothly or not. Check bearing of brass axle Transport Roller if it is loose or not this process prevents reject error.
9. Check the solenoid how it is working in the Picker and Pinch Roller if they are in the correct position whether it touches the banknote and it is not close feed (ask the operator in case of fail-safe)
10. Check and clean DM1, DM2 and all stacker points also check continuous belt and roller if it is corroded or worn out.
11. Check the back of the clutch including plate if rusted or corroded, clean if necessary.
12. Turn on the machine go to the supervisor mode then select component test mode to check the voltage rate of all sensor points , testing of all solenoid, check the banknote feed , rocker tray by BN view program, adjust rocker tray then test run the machine with the operators.
13. Print event report again after the technicians repair the machine.
14. Stand by for about 20-30 minutes with the operators and teach them the basic troubleshooting.

ผลลัพธ์ (อังกฤษ) 2:

The customer goes to 1. When The Technicians Site The technician Will inquire to The customer About The Nature of The machine problem.
2. Then, Print Report The event and all Error Check Before Working.
3. Open all machine covers including DM1, DM2 to check the belts, mechanical components of the machine (test mode). Check IF there are problems.
4. Turn off the machine, start cleaning the machine - should close Unit Sensor before using the blower. After Finished Cleaning Sensor Unit for The Take out Cleaning.
5. Check The position of Suction Tray Set Rocker Band and IF it is in Correct position, Check The Thickness of Suction band and properly Adjust The Locker tray.
6. Always Check The Rotor Valve, When The technician goes to PM Check The Bearing Inside IF it is abnormal Change or Repair immediately.
7. Check Belt, O-ring, Toothed wheel Bearings include all of The Whole machine IF IF The Bearing damaged or does Not Fit Together The technician should immediately Change or Repair.
8. Check sensor unit, remove Roller (Part no.158853011) Brass bearing (Part no.201448000) for cleaning and check if it is turning smoothly or not. Check axle Transport Roller Bearing of Brass IF it is Not Loose or reject this prevents Error Process.
9. Check The Solenoid How is it Working in The Pinch Roller Picker and IF they are in The Correct position Whether it touches The banknote and it is close Not Feed (ask operator in The Case of Fail-Safe)
10. Check and Clean DM1, DM2 and all points also stacker Check Continuous Belt and Roller IF it is corroded or worn out.
11. Check The back of The Clutch Plate including IF rusted or corroded, Clean IF necessary.
12. Turn on the machine go to the supervisor mode then select component test mode to check the voltage rate of all sensor points, testing of all solenoid, check the banknote feed, rocker tray by BN view program, adjust rocker tray then test run the machine with. The operators.
13. The event Print Report Again After The machine Repair Technicians.
14. Stand by for about 20-30 minutes with the operators and teach them the basic troubleshooting.